Forced Induction

The Edelbrock #91171 Wide-Band Oxygen Sensor is a replacement Sensor for use with Edelbrock #91170 2-Channel Wide Band Air Fuel Ratio Monitor and Edelbrock #3532 Wide Band Air Fuel Ratio Monitor. Includes a Bosch LSU 4.2 Sensor with square connector for Edelbrock 2 and...

The 8898 is a hard anodized billet aluminum water pump pulley. This pulley is designed to work with our 8896 LS water pump. This pulley is a universal type design that will work with belt offsets of most GM Gen III and Gen IV...

Edelbrock Replacement Heat Exchanger for Mazda MX-5 Supercharger Kit (PN 15540)

Edelbrock Grooved 10 Rib 74mm Pulley - Drop Ship Only

When choosing to upgrade your engine to modern fuel injection, look no further than Edelbrock's Pro-Flo 4 EFI systems. Edelbrock has been delivering the best combination of dyno proven electronic fuel injection performance for over 40 years. Pro-Flo 4 is not just a replacement...

The Edelbrock #36020 Pro-Tuner EFI Pressure Sensors are intended to be used with Edelbrock's Pro-Tuner EFI system, but may be used with other systems using the supplied connector and wiring. They are configurable to most aftermarket ECUs. If you are using another aftermarket ECU,...

Edelbrock Manifold Absolute Pressure Sensor is used in our #7118 Performer RPM LS1 Manifold as well as the Edelbrock E-Street, Pro-Flo 2, Pro-Flo 3 & Pro-Flo 4 Systems.

The Edelbrock #36018 Throttle Position Sensor can be used on the Competition Throttle Bodies (Universal 4-barrel Throttle Bodies). The Edelbrock #36018 Throttle Position Sensor is a service item to support the Edelbrock line of throttle bodies and EFI kits. It rotates clockwise and is...

Edelbrock Idle Air Control Valve (Iac) And Gasket (Hitachi)

Idle Air Control Valve #36015 GM Stepper Type

The Edelbrock #36013 is a Replacement Bosch 4-wire switching, Narrow-Band Oxygen Sensor for ProFlo2, ProFlo2/XT, and Pro-Tuner EFI Systems.

Edelbrock part #36012 Coolant Temp Sensor for E-Street and Pro-Flo 3 & Pro-Flo 4 systems. This Delphi Temperature Sensor designed for measurement of coolant, oil and other automotive fluids. It has 3/8-18 NPT threads with thread sealant pre-applied and can be used on a...

The Edelbrock #3591 is a Replacement Narrow-Band Oxygen Sensor For ProFlo1 (#3500 Series) EFI Systems. It is a Bosch 3-Wire, Heated Sensor. It includes Replacement O2 Sensor and Weld-In Bung.

Edelbrock part #3589 Pro-Flo EFI replacement coolant temperature sensor is available for Pro-Flo and Pro-Flo XT EFI systems, Brass, Natural, 3/8 in. NPT Thread Size.

The Edelbrock #3588 Air Temp Sensor with 3/8"-18 NPT threads. This Edelbrock #36018 Threaded Air Temp Sensor has a range from -40 to 284 Deg Fahrenheit.

Edelbrock Manifold Absolute Pressure Sensor is for use with first generation Edelbrock Pro-Flo EFI systems.

Edelbrock part #3586 Pro-Flo EFI Fuel Pump Relay. Edelbrock Pro-Flo fuel pump relays can help restore proper function to your Pro-Flo EFI system so that it can perform its optimum best

The Edelbrock #3578 Air Temp Sensor is for push in connections. This Edelbrock #36018 Air Temp Sensor includes a rubber grommet and has a range from -40 to 284 Deg Fahrenheit.

Edelbrock part #3546 for Pro-Flo 3 Fuel Sensor, It includes a 1/8-27 NPT fuel pressure sensor with a -6 AN fuel pressure take-off fitting

Edelbrock Wire Separator Kit #22799 will organize spark plug wires on 4-, 6- and 8-cylinder engines and includes six separators (two 2-wire, two 3-wire and two 4-wire) designed to work with wire diameters up to 8.5mm. Edelbrock Separators are constructed of glass-fiber-reinforced nylon for...

Edelbrock part #22744 Max-Fire Coil-On-Plug ignition coil pack is for use with 1997-2014 Ford 4.6L, 5.4L and 6.8L engines with 2-valve cylinder heads. It's a direct bolt-on with OEM DIS electronic controls and aftermarket high performance ignition systems. Edelbrock Max-Fire Coil On Plug ignition...

Edelbrock Part #15988 Edelbrock Competition Air Intake kit provides the increased airflow needed for 2010-14 Camaro SS racing applications. It includes a 9in. long reusable open element filter, plastic shroud and all necessary hardware for installation. This kit will utilize the factory MAF sensor.This...

The Edelbrock supercharger Stage 1 Street system part #1598 for 2010-2013, Manual Trans, Camaro SS increases the performance of your LS3 engine to 599 horsepower and 547 ft-lbs of torque at the crank. The core of this system is the Eaton Gen VI 2300...

Edelbrock Hardware Kit part #15905 includes all parts necessary to install a #1590 or #1591 Edelbrock Supercharger System on a 2010-2013 Corvette equipped with the Grand Sport trim package and a manual transmission. These vehicles have the dry sump oiling system found on the...

The Edelbrock part #15902 kit contains all the parts necessary to upgrade an Edelbrock supercharger Kit part #1590 to the #1591 599 horsepower level. Parts supplied include the Z06 fuel pump and a 3.5" supercharger drive pulley.This Part Fits: Year Make Model Submodel 2008-2013...

The Edelbrock Pro Tuner Supercharger System #15899 is designed for a large group of model-years that include the 2015-20 Ford Mustang GT, GT350 and Bullitt edition Mustangs. This special kit is intended for competition applications and features the modular supercharger inlet that allows the...

The Edelbrock Universal Supercharger System #15885 is intended for Coyote engine swap applications using a Gen 1, Gen 2 or Gen 3 Coyote 5.0L engine. Its compact design fits under the stock hood on most applications and complements the clean look of any engine...

The Edelbrock Stage II Upgrade Kit part #15882 allows customers using the 1588/15880 supercharger (2011-14 5.0L Mustang) to upgrade to stage 2. The Edelbrock Stage II Upgrade Kit part #15882 includes a 3.25in. supercharger pulley, complete competition air intake system, Gatorback belt, and an...

The Edelbrock supercharger Stage 1 Street system part #15880 for 2011-14 Mustangs increases the performance of your Coyote 5.0L 4V engine to 559 horsepower and 503 ft-lbs of torque at the crank when used with Edelbrock tune (kit supplied without a programmer). The core...

The Edelbrock supercharger Stage 1 Street system part #1588 for 2011-14 Mustangs increases the performance of your Coyote 5.0L 4V engine to 559 horsepower and 503 ft-lbs of torque at the crank. The core of this system is the Eaton Gen VI 2300 TVS...

This 8-Rib Belt Drive Conversion Kit is for use with Edelbrock equipped 2013-2020 5.0L Mustangs. It enables the use of a wider, 8-Rib supercharger pulley instead of the standard 6-Rib design. The 8-Rib belt drive will allow customers to substantially increase boost levels by...

Edelbrock 3.25in. part #15873 pulley allow you to fine tune the airflow and performance of your Edelbrock Supercharger System to your preference. Edelbrock pulley is a 8-rib design for use with any of our Professional Tuner systems. Edelbrock pulley feature a black anodized finish.-...

Edelbrock 3.00in. part #15872 pulley allow you to fine tune the airflow and performance of your Edelbrock Supercharger System to your preference. Edelbrock pulley is a 8-rib design for use with any of our Professional Tuner systems. Edelbrock pulley feature a black anodized finish.-...

Edelbrock 2.75in. part #15871 pulley allow you to fine tune the airflow and performance of your Edelbrock Supercharger System to your preference. Edelbrock pulley is a 8-rib design for use with any of our Professional Tuner systems. Edelbrock pulley feature a black anodized finish.-...

Edelbrock 2.625in. part #15870 pulley allow you to fine tune the airflow and performance of your Edelbrock Supercharger System to your preference. Edelbrock pulley is a 8-rib design for use with any of our Professional Tuner systems. Edelbrock pulley feature a black anodized finish.-...

The Edelbrock supercharger Stage 2 system part #15856 for 2005-09 Ford Mustang increases the performance of your 4.6L 3V engine to 529 horsepower and 494 ft-lbs of torque at the crank. The core of this system is the Eaton Gen VI 2300 TVS rotating...

Edelbrock 2.750in. pulley part #15854 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15854 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock 3.250in. pulley part #15852 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15852 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock Comkpetition 3.250in. pulley part #15850 allows you to fine tune the air flow and performance of your E-Force C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15850 features a 10-rib design for use with our E-Force street rod and muscle...

Edelbrock 3.500in. pulley part #15849 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15849 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock 3.750in. pulley part #15848 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15848 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock 3.875in. pulley part #15847 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15847 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock 4.000in. pulley part #15846 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15846 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

Edelbrock 4.125in. pulley part #15845 allows you to fine tune the airflow and performance of your Edelbrock C7 Corvette or Enforcer Supercharger system to your preference. The Edelbrock #15845 features a 10-rib design for use with our Edelbrock street rod and muscle car Supercharger...

The performance-proven Edelbrock modular-inlet supercharger is now available for owners of 2015-2017 Ford Mustangs with the 5.0L Coyote engine. Our new Edelbrock Supercharger System W/O Tuner #158380 is a bolt-on kit that produces an impressive 690 horsepower with 588 ft-lbs of torque. At the...

The performance-proven Edelbrock modular-inlet supercharger system is now available for owners of 2015-2017 Ford Mustangs with the 5.0L Coyote engine. Our new Edelbrock supercharger #15838 is a complete bolt-on kit that produces an impressive 690 horsepower with 588 ft-lbs of torque. At the heart...

The Edelbrock supercharger Stage 1 part #158360 is designed for use with 2018 Ford F150 With Gen III DI/PI 5.0L Coyote engine and 10-Speed Auto trans. The core of this system is the Eaton Gen VI 2650 TVS rotating assembly with a four-lobe design...

The Edelbrock Supercharger System part #158360 is designed for use on a 2018 Ford F150 with Gen III DI/PI 5.0L Coyote engine and 10-Speed automatic transmission. The heart of this system is the high-efficiency Eaton Gen VI 2650 TVS rotating assembly with a four-lobe...

Offering a 157hp increase at the tires over stock, the Edelbrock 158333 kit will unleash the max potential of your truck. Edelbrock's engineers collaborated with Garrett on the design of all new turbos for the 3.5L EcoBoost trucks. These new direct bolt in turbos...

Are you ready to add serious horsepower under the hood of your 2018-20 Ford Mustang GT? The Edelbrock supercharger Kit #15832 is a 50-state emissions-legal system that is dyno-proven to produce 623 horsepower and 510 ft-lbs of torque to the rear wheels with no...